Announcement

Collapse
No announcement yet.

WTB: TiLite Brake clamp / bracket

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    WTB: TiLite Brake clamp / bracket

    Looking to buy one of these if someone has a spare just collecting dust. For 1-1/4" frame size.

    https://www.spinlife.com/TiLite-Whee...roductID=93433

    #2
    That's rape and extortion put together. Shame on you Spinlife!

    Look here:

    https://hdsupplysolutions.com/p/black-aluminum-wheel-locks-for-7-8-tube-package-of-2-p121077

    Search "wheel locks."

    Ti
    "We must overcome difficulties rather than being overcome by difficulties."

    Comment


      #3
      Originally posted by titanium4motion View Post
      That's rape and extortion put together. Shame on you Spinlife!

      Look here:

      https://hdsupplysolutions.com/p/black-aluminum-wheel-locks-for-7-8-tube-package-of-2-p121077

      Search "wheel locks."

      Ti
      Wow no kidding. But that link you shared only has them for 7/8" and 1" tubing. I need one for 1-1/4" tubing. (my chair is a ZRA)

      Haven't been able to find any less expensive than Spinlife but I'll keep looking.

      Comment


        #4
        I switched to the composite brakes a few years ago. If I can find these brackets in my recycle box you can have them. I have a nine-year-old ZRa so they would probably work for you.

        Comment


          #5
          I found two half clamps. They are identical and both have fasteners so I'm assuming they're both inner or both outer. They have counterbored slots for the fasteners, probably 10-32 unless they're metric. They are 1.5" wide. My tubes are 1.25" in diameter. If the inner and outer clamps are supposed to be the same, we may have a winner. If so PM me your address and I'll send them to you.

          Comment


            #6
            Originally posted by endo_aftermath View Post
            I found two half clamps. They are identical and both have fasteners so I'm assuming they're both inner or both outer. They have counterbored slots for the fasteners, probably 10-32 unless they're metric. They are 1.5" wide. My tubes are 1.25" in diameter. If the inner and outer clamps are supposed to be the same, we may have a winner. If so PM me your address and I'll send them to you.
            PM sent!

            Comment


              #7
              The clamp from endo_aftermath ended up being for 1" tubes. Back to square one and still looking for a clamp if anyone has one.

              Comment


                #8
                I should have a usable one but have not located it yet. If I can get out to the garage tomorrow I'll look there. It's yours if I can find it.
                I have had periodic paralysis all my life. I lost my ability to walk in 2011 beginning with a spinal block, which was used for a hip fracture caused by periodic paralysis.

                Comment


                  #9
                  Originally posted by nonoise View Post
                  I should have a usable one but have not located it yet. If I can get out to the garage tomorrow I'll look there. It's yours if I can find it.
                  Sounds great, thanks!

                  Comment


                    #10
                    Google The Aftermarket Group, they carry tons of parts.

                    Comment


                      #11
                      Originally posted by Oldtimer View Post
                      Google The Aftermarket Group, they carry tons of parts.
                      They don't carry the bracket either.

                      I just modeled up a bracket and key hook combo for 3D printing tonight and sent it off for quote. Cause once I get a bracket anyway I'd have to make a piece for it to be my key and phone holder. This one I modeled should do it all one stop shop.

                      Comment


                        #12
                        Originally posted by Oldtimer View Post
                        Google The Aftermarket Group, they carry tons of parts.
                        They don't carry the bracket either.

                        I just modeled up a bracket and key hook combo for 3D printing tonight and sent it off for quote. Cause once I get a bracket anyway I'd have to make a piece for it to be my key and phone holder. This one I modeled should do it all one stop shop.

                        http:///forum/showthread.php?260590-...=1#post1836964 is my original hook on one of my chairs. The closest thing I've seen made to it is one that ADI used to make.

                        Comment


                          #13
                          I found it. PM me your snail address. I thought I had two, but could only find one for some reason.
                          I have had periodic paralysis all my life. I lost my ability to walk in 2011 beginning with a spinal block, which was used for a hip fracture caused by periodic paralysis.

                          Comment


                            #14
                            Originally posted by nonoise View Post
                            I found it. PM me your snail address. I thought I had two, but could only find one for some reason.
                            Here it is combined with the clamp you send me, all said and done. The 3D printed part cost me $4 and now I have a rock solid double key/phone/work badge hook on my backup chair. I had it printed with 100% infill so it should have no problem holding up to the weight of those items. Would not handle the impacts of tossing the chair around if you break down the chair to go load into a vehicle though. Which I don't do.

                            Anyone interested in doing the same thing shoot me a PM and I can send you the .stl file to have printed if you have a place that can print for you. Or I could have a few printed and send to those that want them.
                            Attached Files

                            Comment

                            Working...
                            X